Sprinkler
Sprinkler: A sprinkler is a device used to spray water. Sprinklers are used to water plants or grass, or to put out fires in buildings. a device perforated with small holes that is attached to a garden hose or watering can and used to spray plants, lawns, etc.
Gauges
Gauges: A gauge or gage, in science and engineering, is a device used to make measurements or in order to display certain dimensional information. A wide variety of tools exist which serve such functions, ranging from simple pieces of material against which sizes can be measured to complex pieces of machinery.
Industrial Belts
Industrial Belts: Industrial belts are designed to transmit power between shafts and capable of moving at very high shaft speed. Industry has different use of industrial belts according to theirs need. These belts are round belts, v belts, flat belts, timing belt and PVC conveyor belt etc.
Electric Chain Pulley Blocks
Electric Chain Pulley Blocks: Electric chain hoist consist of an induction motor with a break to hold the load lifted on it. It’s electrical panel board and the motor with pulley coupled to the hoist, with a pendant operating station hanging with the help of a steel wire rope at a height of the operator friendly use.
Webbing Slings
Webbing Slings: These web slings are lightweight, durable, and flexible so that they can be easily handled and rigged to a load. The Nylon and polyester web slings are unaffected by oil and grease and offer good chemical resistance.
Motorized Actuator
Motorized Actuator: A valve actuator is the mechanism for opening and closing a valve. Manually operated valves require someone in attendance to adjust them using a direct or geared mechanism attached to the valve stem.
Both Side Gum Patti
Both Side Gum Patti: Created by applying a thin adhesive layer to each side of a carrier substrate material, double sided tape, also known as double-coated tape or double-faced tape, is widely used by a vast array of industries for applications such as bonding, holding, mounting, splicing and packaging.
PTFE Gaskets
PTFE Gaskets: Polytetrafluoroethylene (PTFE) is a synthetic fluoropolymer of tetrafluoroethylene that has numerous applications. It is also known by the common trade name Teflon®, which is trademarked by DuPont. PTFE can be modified for use as a gasketing material with strong chemical resistance properties.
Filler Wires
Filler Wires: Welding is a fabrication or sculptural process that joins materials, usually metals or thermoplastics, by using high heat to melt the parts together and allowing them to cool causing fusion.
Welding Machines
Welding Machine: Welding is the process of joining two materials like steel, aluminum, brass, stainless steel, plastic or polymer and fusing them. Welder is the equipment used in welding. In this type of welding, a consumable electrode coated in flux is used to lay the weld. Electric current is provided by the welding power supply.
Welding Cable
Welding cable: Welding cable is designed for use in electric arc-welding machines to power an electrode, a specially designed metal rod, that conducts a charge. The charge carried by the electrode is needed to produce an electric arc, the heat source, between the electrode and the metals being welded.
Welding Accessories
Welding Accessories: Welding gloves, aprons and helmets, dust masks, extraction systems and other safety equipment. Chipping hammers and wire brushes. Gas nozzles and contact tips for MIG/MAG welding. Tungsten rods for TIG/GTAW welding. Abrasive discs for angle grinders. Electrodes for resistance spot welding. Angle grinders. Electrode drying ovens.
Welding Hoses
Welding Hoses: Hoses are used across industries to transfer various types of fuel gases for welding and cutting. Fuel gases such as acetylene, propane, and butane utilize different types of welding hoses. A clamp helps lock the gas on the hose end of the nipple.
Electrode
Electrode: An electrode is a solid electric conductor that carries electric current into non-metallic solids, or liquids, or gases, or plasmas, or vacuums. Electrodes are typically good electric conductors, but they need not be metals.
Temperature Gauges
Temperature Gauges: A temperature gauge is a device used to indicate the temperature of an item being monitored. The display can be an analog dial, an analog range, or a digital readout.
Pressure Gauge
Pressure Gauge: Pressure measurement is the analysis of an applied force by a fluid (liquid or gas) on a surface. Pressure is typically measured in units of force per unit of surface area. Many techniques have been developed for the measurement of pressure and vacuum. Instruments used to measure and display pressure in an integral unit are called pressure meters or pressure gauges or vacuum gauges. A manometer is a good example, as it uses the surface area and weight of a column of liquid to both measure and indicate pressure. Likewise, the widely used Bourdon gauge is a mechanical device, which both measures and indicates and is probably the best-known type of gauge.
Hand Gloves
Butterfly Valve: Butterfly Valve has a similar operation like Ball Valve. It is used to block the flow of Media (like Water, Chemical etc.). Generally, user preferred butterfly valve instead of ball valve because it is economical. It is available in Minimum size of 40mm. Butterfly valve has a simple structure which is contain Body, Seal, Stem, Rubber seat (Nitrile, EPDM, Viton), Disc (Sg Iron, SS) & Lever. It is easy to use by Lever & Gear. It will also operate by Actuator. Basically, up to 150mm butterfly valve is operated by Hand Lever & Above 150mm butterfly valve is Gear Operated.
There is various type of Butterfly Valves Like: –
According to Flow of circuit
- Wafer Type Butterfly Valve
- Semi Lug Type Butterfly valve.
- Lug Type Butterfly valve.
- Double Flanged Type Butterfly valve.
- Motorized Butterfly valve.
Butterfly valve is also known as quarter-turn valves in the family of Valves. Butterfly valve has a different type of pressure rating & Different usage which depends on MOC of rubber & Disc. Butterfly valve available in SG Iron (Cast Iron), Cast Steel, SS304, SS316, Aluminum body.
Accessories
Power Tools: A power tool is a tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools. The most common types of power tools use electric motors. Internal combustion engines and compressed air are also commonly used. Other power sources include steam engines, direct burning of fuels and propellants, such as in powder-actuated tools, or even natural power sources such as wind or moving water. Tools directly driven by animal power are not generally considered power tools.
Drill Machines
Drill Machines: A drill is a tool primarily used for making round holes or driving fasteners. It is fitted with a bit, either a drill or driver, depending on application, secured by a chuck. Some powered drills also include a hammer function.
Drills vary widely in speed, power, and size. They are characteristically corded electrically driven devices, with hand operated types dramatically decreasing in popularity and cordless battery powered ones proliferating. Drills are commonly used in woodworking, metalworking, machine tool fabrication, construction and utility projects. Specially designed versions are made for medicine, space, and miniature applications.
Reamers
Reamers: A reamer is a type of rotary cutting tool used in metalworking. Precision reamers are designed to enlarge the size of a previously formed hole by a small amount but with a high degree of accuracy to leave smooth sides.
Tap Sets
Tap Sets: Tapping is when you threads are cut into a hole. A die set is used to cut threads onto a cylinder (bolt). To use a tap or a die, first determine the number of threads per inch (TPI) of the part to be fixed.
Drills
Drills: The drill’s mechanism is actually quite simple: A trigger switch activates an electric motor, which in turn drives a rotating chuck. Numerous accessories can fit into in the chuck, allowing the drill to bore holes, drive screws, and sand, polish, and grind a wide variety of materials.
Hammers
Hammers: A hammer is a tool consisting of a weighted “head” fixed to a long handle that is swung to deliver an impact to a small area of an object. This can be, for example, to drive nails into wood, to shape metal (as with a forge), or to crush rock. Hammers are used for a wide range of driving, shaping, and breaking applications.
Pliers
Pliers: Pliers are a hand tool used to hold objects firmly, possibly developed from tongs used to handle hot metal in Bronze Age Europe. They are also useful for bending and compressing a wide range of materials.
Allen Keys
Allen Keys: A hex key, Allen wrench or Allen key, is a simple tool used to drive bolts and screws with hexagonal sockets in their heads. The tool is usually formed of a single piece of hexagonal rod of hard steel, with blunt ends that are meant to fit snugly into the screw’s socket, bent in an “L” shape with unequal arms.
Hydraulic & Manual Jacks
Hydraulic & Manual Jacks: Working Principle of HYDRAULIC JACK or HYDRAULIC PRESS. The hydraulic jack is a device used for lifting heavy loads by the application of much smaller force. It is based on Pascal’s law, which states that intensity of pressure is transmitted equally in all directions through a mass of fluid at rest.
Tools Kits
Tools Kits: Tools and equipment are terms that are often used interchangeably without knowing the actual difference between tools and equipment, but in fact, they have different definitions. Tools and equipment are not only two words that are often used in day to day life, but also two utensils that are often used every day as well.
Tool Set has the tools you need to tackle a variety of tasks around the house. Whether you’re doing basic repairs, hanging pictures or cutting through boxes, this tool kit will equip you with the high-quality essentials required to complete many DIY projects.
Raised Face
Raised Face Flange: The Raised Face flange is the most common type used in process plant applications, and is easily to identify. It is referred to as a raised face because the gasket surfaces are raised above the bolting circle face
Welding Neck Flange
Welding Neck Flange: A weld neck flange consists of a circular fitting with a protruding rim around the circumference. Generally machined from a forging, these flanges are typically butt welded to a pipe. The rim has a series of drilled holes that permit the flange to be affixed to another flange with bolts.
Copper Pipe
Copper Pipe: Copper pipes are commonly used in the construction industry for water supply lines and refrigerant lines in HVAC (heating, cooling, and air-conditioning) systems. Copper pipes can be manufactured as soft or rigid copper and offer excellent corrosion-resistance and reliable connections
Plastic Pipe
Plastic Pipe: Plastic pipe is a tubular section, or hollow cylinder, made of plastic. It is usually, but not necessarily, of circular cross-section, used mainly to convey substances which can flow liquids and gases (fluids), slurries, powders and masses of small solids.
G.I Pipe
Induskart is one of the leading GI Pipe Supplier in India. G.I Pipe: Galvanized iron pipes are made up of an alloy of iron or steel with a coating of zinc on it . This is done as zinc helps in the prevention of corrosion. This will help the pipe to get exposed to the environment without hesitating with the issue of rust.
GI pipe contains a large proportion of carbon in it which makes it hard. Pure iron in nature is very ductile and has no carbon in it. The zinc helps in giving it a longer period of life.
They are available in various variants and sizes. They are also comparatively cheap, lightweight, and cost-effective. GI pipes are used in many plumbing operations such as welding, treating sewage, sprinkler systems, etc.
Cast Iron Pipe
Cast Iron Pipe: Cast iron pipe is a pipe which has had historic use as a pressure pipe for transmission of water, gas and sewage, and as a water drainage pipe during the 17th, 18th, 19th and 20th centuries.
Nipples
Nipples: A nipple is a fitting, consisting of a short piece of pipe, usually provided with a male pipe thread at each end, for connecting two other fittings. The length of the nipple is usually specified by the overall length with thread. It may have a hexagonal section in the center for a wrench to grasp (sometimes referred to as a “hex nipple”), or it may simply be made from a short piece of pipe (sometimes referred to as a “barrel nipple” or “pipe nipple”). A “close nipple” has no unthreaded area; when screwed tightly between two female fittings, very little of the nipple remains exposed.
Sockets
Sockets: A Socket Weld is a pipe attachment detail in which a pipe is inserted into a recessed area of a Valve, fitting or flange. In contrast to buttweld fittings, Socket Weld fittings are mainly used for small pipe diameters (Small Bore Piping); generally, for piping whose nominal diameter is NPS 2 or smaller.
Tee
Tee: Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90° to the connection to the main line. It is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings.
Elbows
Elbows: An elbow is installed between two lengths of pipe (or tubing) to allow a change of direction, usually a 90° or 45° angle; 22.5° elbows are also available. The ends may be machined for butt welding, threaded (usually female), or socketed. When the ends differ in size, it is known as a reducing (or reducer) elbow.
Pin Type Anchor
Pin Type Anchor: Pin type anchor bolts find their use in soft masonry to reduce the effect of vibration and pressure. The most significant advantage of using these bolts is that it can be replaced without affecting the holding strength of the anchor system.
Frame Fixing Anchors
Frame Fixing Anchors: Plastic frame fixings are the ideal solution for the fixing of facade constructions, roof substructures, heavy wall cabinets, squared timbers, cable trays, gates and doors. With the long plug shaft, these can be directly secured in the building substrate through the attachment part.
Sleeve Anchors
Sleeve Anchors: Sleeve anchors are the most versatile masonry expansion anchors because they can be used in a variety of base materials, including concrete, brick, and block. They are available in a wide variety of diameters, lengths, and head styles. The available head styles are acorn, hex nut, flat, countersunk, and round head.
Bullet Anchors
Bullet Anchors: Bullet type anchor shell with internal thread for pre-positioned installation. When the bullet is placed in shell & hit with a setting tools it slides forward & the inside part of shell expands and takes the grip in the wall.
Threaded Rod & Studs
Threaded Rod & Studs: The threaded rod Fairfield is basically used to fasten wood or metal together. It acts as a pin that is used to connect two materials together. They are also used to stabilize structures by inserting them into concrete or wood during repair.
Studs & Nuts
Studs & Nuts: A bolt with threads on both ends designed to be screwed permanently into a fixed part at one end and to receive a nut on the other. A bolt is a threaded fastener mated with a nut. A screw has either pre-formed or self-made external threads. A stud is an externally threaded headless fastener. One end mate with a tapped component and the other with a standard nut.
Nylon Anchor
Nylon Anchor: Nylon Anchors are pre-assembled through fixing, a light duty nail expanding for solid masonry and hollow wall constructions. The design of the expansion nail used in the Nylon Anchor is such that it can be removed if need be.
Sanitary Fixing Anchor
Sanitary Fixing Anchor: Nylon Anchors are pre-assembled through fixing, a light duty nail expanding for solid masonry and hollow wall constructions. The design of the expansion nail used in the Nylon Anchor is such that it can be removed if need be.
Safety Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Safety Valve: A safety valve is a valve that acts as a fail-safe. An example of safety valve is a pressure relief valve, which automatically releases a substance from a boiler, pressure vessel, or other system, when the pressure or temperature exceeds preset limits.
Ball Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Ball Valve: A ball valve is a form of quarter-turn valve which uses a hollow, perforated and pivoting ball to control flow through it. It is open when the ball’s hole is in line with the flow and closed when it is pivoted 90-degrees by the valve handle. Ball Valve is a Shutoff type valve which is used to control the flow of Fluid (Liquid/Gas). The valve basically has ball inside it which is used to control the flow, the ball is attached with an external lever which opens/closes the passage for fluid to pass through the valve. Usually ball valves are used for sizes below 100MM, above that gate valves are used instead of ball valve. Ball valves comes in various type and in various MOC
Check Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Check Valve: A check valve, clack valve, non-return valve, reflux valve, retention valve or one-way valve is a valve that normally allows fluid to flow through it in only one direction. Check valves are two-port valves, meaning they have two openings in the body, one for fluid to enter and the other for fluid to leave.
Non Return Valve
A non-return valve is a simple mechanical device that is used to allow a medium pressure flow in any one direction. It helps the fluid to travel with a medium velocity in one direction and prohibits the reverse flow of the fluid caused by very high pressure. The non-return valves cause a very high-pressure drop which is a drawback for it. it also helps to prevent the upstream types of equipment that could get damaged by reverse flow such as water pumps. They are also known as check valves. The non-return valves are available in various types such as clapper type, swing type, spring-loaded, etc. they could be manually operated or also by automated actuation.
Strainer Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Strainer: Y-Strainers are devices for mechanically removing unwanted solids from liquid, gas or steam lines by means of a perforated or wire mesh straining element. They are used in pipelines to protect pumps, meters, control valves, steam traps, regulators and other process equipment.
Gate Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Gate Valve: A gate valve, also known as a sluice valve, is a valve that opens by lifting a barrier out of the path of the fluid. Gate valves require very little space along the pipe axis and hardly restrict the flow of fluid when the gate is fully opened. The gate faces can be parallel but are most commonly wedge-shaped.
Sluice Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Sluice Valve: A gate valve, also known as a sluice valve, is a valve that opens by lifting a barrier out of the path of the fluid. Gate valves require very little space along the pipe axis and hardly restrict the flow of fluid when the gate is fully opened. The gate faces can be parallel but are most commonly wedge-shaped.
Knife Edge Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Knife Edge Valve: Knife Edge Valve are designed mainly for on-off and isolation services in systems with high content of suspended solids. The knife gate valves are especially beneficial for handling slurry, viscous, corrosive and abrasive media. The valves have a minimized pressure drop in fully open position, they are easy to actuate, they have a relatively low weight and are cost effective.
Knife Edge Valve are designed to work in some of the most harsh environments, typically having a sharpened blade to cut through heavy liquids.
Foot Valve
Valve: Valves are for starting or stopping flow, regulating or throttling flow, preventing back flow or relieving and regulating pressure in fluid or gaseous handling applications. Common valve types include: Ball, Butterfly, Check, Diaphragm, Gate, Globe, Knife Gate, Parallel Slide, Pinch, Piston, Plug, Sluice, etc.
Foot Valve: A foot valve is a type of check valve that is typically installed at a pump or at the bottom of a pipe line (hence the name). Foot valves act like ball check valves, but have an open end with a shield or screen over it to block debris from entering the line.
Plug Valve
Plug Valve: Plug valves are valves with cylindrical or conically tapered “plugs” which can be rotated inside the valve body to control flow through the valve. The plugs in plug valves have one or more hollow passageways going sideways through the plug, so that fluid can flow through the plug when the valve is open.
Ferrule Cock
Ferrule Cock: Ferrule Cocks incorporate a packed gland spindle and have a union outlet for connection to all ferrule bends or adaptors. RMC TPFNR Ferrules are for under pressure tapping. They incorporate a non-return gunmetal jumper valve and a high-density polyethylene tapered closing plug.
Fire Hydrant Landing Valve
Fire Hydrant Landing Valve: A Fire Hydrant Valve is a pipe fitting that help to regulate, direct or control the flow of fire suppressing agents by opening, closing or partially obstructing passageways in the hose connectors. Non-return valves stop the fire suppressing agent from flowing in the wrong direction.
Needle Valve
Needle Valve: A needle valve is a type of valve with a small port and a threaded, needle-shaped plunger. It allows precise regulation of flow, although it is generally only capable of relatively low flow rates.
Bonnet Wheel Valve
Bonnet Wheel Valve: The cover for the opening sin the body is the bonnet, and it is the second most important boundary of a pressure valve. Like valve bodies, bonnets are in many designs and models available. A bonnet acts as a cover on the valve body, is cast or forged of the same material as the body. It is commonly connected to the body by a threaded, bolted, or welded joint. During manufacture of the valve, the internal components, such as stem, disk etc., are put into the body and then the bonnet is attached to hold all parts together inside.
Blow Down Valve
Blow Down Valve: Blowdown valves are commonly used in boilers in order to drain dissolved solids from the boiler water. These valves are fitted on the drain lines of the boilers. One or multiple blowdown valves are used in boilers depending upon its design and purpose.
Gas Valve
Gas Valve: A gas control valve can be found on any appliance that utilizes gas. These valves are vital for the operation and safety of any gas appliance. The valve does exactly what it sounds like, it controls the amount of gas flowing to create a steady flow without allowing any gas to leak.
Gauge Cock
Gauge Cock: Gauge Cocks provide an economical way to shut off the flow of air to the pressure instrument, thereby allowing the instrument to be isolated from the pressure media or removed from service. Gauge Cocks are constructed from brass and are intended for use on air lines where leakage is not of concern.
Fusible Plug
Fusible Plug: A fusible plug operates as a safety valve when dangerous temperatures, rather than dangerous pressures, are reached in a closed vessel. In steam engines the fusible plug is screwed into the crown sheet (the top plate) of the firebox, typically extending about an inch (25mm) into the water space above it.
Relief Valve
Relief Valve: A relief valve or pressure relief valve is a type of safety valve used to control or limit the pressure in a system; pressure might otherwise build up and create a process upset, instrument or equipment failure, or fire.
